empire gas logs won't light

You dont actually need to get close to the pilot setting - about halfway between LO and pilot will be sufficient to turn the main part of the logs off while keeping the pilot lit. Pilot light on gas logs wont stay lit with logs on.

Gas Fireplace Pilot Light On But Won T Ignite Here S How To Fix It

3- Close tap and check for gas leak.

. Release knob if pilot stays lit If not go back to step 3 and repeat. Bad thermocouples or electric ignition can also cause a problem. Next follow pilot lighting instructions to light pilot.

Once the pilot is lit hold the pilot valve in for 60 seconds. Gas fireplaces if. Step 3 If gas is coming out of the pilot but it still wont light clear away any gunk sitting between the igniter and thermocouple using a can of compressed air.

Click here to send an email to our Customer Service Department. Before you go too far in your attempt to solve the problem you should check to make sure your pilot light is lit. Oxypilot Is Blocked With Dust or Soot.

This is where the electronic ignition system comes into play. I have new RH Peterson Real Fyre gas logs. Today I had them on for five hours then suddenly the fire went out and they started beeping at me.

Still having trouble with the heater. Check your pilot light. While cooler air drops.

With control knob in push the piezo ignitor in continuously until pilot ignites every 3-5 seconds. If your fireplace has an electric igniter. Call center representative at.

If gas is coming out of the pilot but it still wont light the spark igniter could be the problem. The main burner orifice must be centered in the venturi tube for proper combustion and to prevent sooting. Jan 29 2006.

They were installed a week ago. The pilot light goes out when you release the pilot button. If gas is coming out of the pilot but it still wont light the spark igniter could be the problem.

Use an air compressor to blow inside the pilot light and the thermocouple. This allows the pilot flame to heat the thermocouple attached to the log. No heat comes from the furnace it shut down.

From Gas Control Valve 1- Turn main gas on and proceed to next step. Gas Fireplace Wont Light FIXEDSimple Steps To Get Your Fireplace Going Again To Warm Your HomeDIY and saveMost often these easy cleaning steps ge. Do not alter log placement from the prescribed layout in this manual.

Keep in mind that the instructions to reset your pilot light. Alleyne says to look for and clear out any debris between the igniter and thermocouple. Only use Empire Logs specially made for this burner.

Once pilot flame is lit keep knob pushed in for 60 seconds. If the knob wont turn turn the knob to off wait 10 minutes and try again. With the logs off the pilot light will stay lit and the flame will work.

When you put it back your pilot flame should be blue or blue-white in color. Air In The Line If applicable first remove the protective cap screw. If these check out the issue could be overloaded fuses or breakers an obstruction gas pressure issues moisture in the gas line or clogged burner ports.

To turn the logs off turn the knob clockwise without depressing towards LO then pilot. The fire burns over a ceramic log to create the illusion of a wood fireplace. Verify the venturi tube is not bent or distorted.

With the logs on the pilot light goes out. With control knob in push the piezo ignitor in continuously until pilot ignites every 3-5 seconds. The oxypilot is a safety device built into the fireplace so that your carbon monoxide levels are kept safe and regulated.

I called the store where I bought them Offenbachers Rockville MD and they told me to disconnect the two wires from the remote. I have new RH Peterson Real Fyre gas logs. Fireplaces Wood Burning and Heating Stoves Flues and Chimneys - Pilot light on gas logs wont stay lit with logs on - We have just purchased vent free gas logs.

If it is low then its a thermocouple. The gas valve is a Mertix Maxitrol GV31. To turn the logs off turn the knob clockwise without depressing towards LO then pilot.

A gas fireplace uses natural gas as opposed to wood to maintain a flame. This is the simplest fix for when your gas fireplace wont stay on. A pilot light that doesnt glow blue is also a problem as this means it is not getting hot enough.

Empire Heating Cooling - Recent Questions Troubleshooting Support. A spark is required to start the fire. I have an Empire Comfort System furnace that sits on the floor with a thermostat on the wall.

It starts a cycle and then shut down before heating house. Turn control knob counterclockwise to the ON. Empire gas logs wont light.

Install logs according to the installation instructions. Almost all of our brochures and manuals are available on our sites below. If the fireplace pilot light is on but wont start make sure your gas valve is turned on and check the fuse or breakers.

Cant find what you want. The pilot is a large blue flame and in contact with the new thermocouple. It really can be as simple as checking your pilot light and turning it on.

Next follow pilot lighting instructions to light pilot. Superior is a brand name of fireplaces and part of Lennox Hearth Products. 2- Loosen inlet tap screw until you hear the air coming out of the tap until gas odor is evident.

You dont actually need to get close to the pilot setting - about halfway between LO and pilot will be sufficient to turn the main part of the logs off. Often times a pilot light wont turn on resulting in absolutely zero flames happening in your fireplace. One of the biggest problems associated with gas fireplaces is related to the pilot light.

Jumped the spill switch or eco switch wires and also checked them for deterioration at the valve end but they are OK. Push in knob this releases the gas to the pilot area only. Brett Richards walks you through how to light the pilot on an Empire Comfort Systems White Mountain Hearth Vent-Free millivolt gas log fireplace system.

Empire 24 Inch Flint Hill Gas Log Set With Vent Free Propane Contour Burner - Manual Safety Pilot. You need a registered gas technician. If the problem isnt fixed it could indicate a bad thermocouple which should be repaired by a professional.

Fireplace Won T Stay Lit This Is How You Fix It Youtube